Card currency swap, QR scanner and adding money from another wallet
TLDR
8 PRs merged, 16 commits across all branches and 15 PRs opened in 5 repos (the Nuri app: 12, the Arkade server: 12, the banking server: 10, the swap server: 4, this site: 1), 8 deployments, +16,719 / -10,813 lines. I worked on 6 features.
The card can now swap between its euro and dollar balances, and the Nuri app does it automatically into your home currency. The QR scanner has a new design with photo upload, adding money from another wallet no longer gets stuck on unsigned orders, and I removed Boltz from the Arkade server.
Card euro and dollar swap
The banking server can now swap between the card’s euro and dollar balances on Wirex. Before, money in the other currency could only leave the card. The swap pays from the card with the same two passkey approvals as a withdrawal, to a deposit address that only comes from Wirex’s quote, and runs once after that payment is mined. If Wirex refuses it, it is marked failed and never retried. The sandbox version got the same change, and on both I fixed the case where the swap reply gets lost: it now counts as unknown, not as “did not run”.
In the app, money that lands on the card in the other currency is now swapped into your home currency automatically, cut to whole cents. Before, it showed up as found money and was withdrawn to the wallet. That sheet is gone for the card, the Bitcoin one stays. A swap Wirex refused after the money left goes to support, same as a failed card withdrawal.
QR scanner with photo upload
The camera fills the top 60% of the scanner and a card fills the bottom 40%, with the title “Who is your recipient?” and Paste and Upload side by side. Upload opens the photo picker and reads the QR code from the picture inside the app without a new native module, so it can go out as an over the air update. A photo without a code shows “No QR code found in this image”. Without camera permission, Paste and Upload still work. Tests pass, but it is not checked on a device or in a browser yet.
Adding money from another wallet
This is the flow where you top up from an external wallet, and the pay page uses the same one. Orders got stuck when the wallet never answered a signature or threw an error, and Continue then failed forever. Now an unanswered signature is asked again, a wallet error gives the order back so Try again gets a fresh price, and an order past its deadline with nothing sent shows “That price expired” right away instead of “Transfer running”. Trust Wallet refused the signature request because a field was missing, that is fixed too.
Paying EURC on Base into the Euro balance used to quote a CoW swap of EURC into itself, so 5 EURC came out as 4.973438. Now the same token on the same chain is a plain 1:1 transfer. Native ETH on Ethereum, Base, Arbitrum and Optimism, POL on Polygon and xDAI on Gnosis work now, with a bit held back for gas, routed through LI.FI. After you accept, the sheet closes and the status pill shows Preparing, Processing, then Completed or failed. All of this is merged.
On the swap server I opened three PRs: a token is found at LI.FI by its contract instead of its symbol, because USDT on Arbitrum is called USDT0 there and got no route. Each swap now returns its funding, settlement and refund transaction, so the activity can label rows exactly instead of “From Wallet” / “To Wallet”. Finished swaps are listed without locks, because a wallet with 56 swaps waited about 7 seconds per list.
Arkade boarding claims and removed Boltz
Claiming an onchain deposit into Arkade failed because its approval lasted 2 minutes while the claim waited 2 to 3 minutes for its round. It lasts 10 minutes now, still bound to the exact coins and amount, merged. On web the claim also missed every round because messages arrived late. I opened a fix that reads them with the browser’s own event stream, that PR is closed and not merged.
I removed every Boltz call from the Arkade server, including a loop that asked it every 15 seconds about each open Lightning receive. The “Payment received” push still comes from the offline claim, which now pages through pending receives itself, oldest first, so an unpaid receive cannot hide a later paid one.
Lightning limits at 100,000 sats
Arkade’s solver raised the Lightning cap from 50,000 to 100,000 sats. Two open PRs follow it: the swap server raises the send cap, and the Arkade server moves to SDK 0.5 and takes receive limits from the solver, 505 to 99,680 sats. Neither is merged, and the live receive check can only run once the solver serves receive.
Push to card and release 0.105.0
I opened push to card on the banking server, signed like SEPA, with the card number sent once to Wirex and never stored. In the app, cards get saved in the address book and push to card asks for the name first and suggests saved cards. I also opened release candidate 0.105.0 with the card auto-swap, the QR scanner and the top-up fixes, and it is not merged yet.